Shifter Slider Cover | Fits 2012-2019 Nissan Versa and Versa Note | Shifter Strip Hole Dust Cover Gate Blind Gasket Boot Trim Jalousie Accordion Surround | DIY Replacement Part

This is a 3D printed replacement shifter slider made with high-quality, durable, and heat-resistant Black TPU material. Designed to fit Fits 2012–2019 Nissan Versa and 2014–2019 Nissan Versa Note models with automatic transmissions. Please note, this is an aftermarket part produced by Celestial Auto Parts, NOT an OEM part from Nissan. This is for the slider piece only, not the entire shifter assembly. The shifter slider is not sold individually by Nissan and is only available as part of the larger shifter assembly, which could cost you hundreds of dollars in parts and labor to replace. If your assembly is in good condition and only the slider is damaged, this 3D-printed TPU replacement is a perfect solution!Designed 🧑‍💻 printed 🏗️ and processed 🔍 entirely in-house from our home 🏡 in 🪅 San Antonio 🌮, 🤠 Texas ⭐, 🇺🇸 USA 🦅. We personally ensure each piece meets high-quality standards.Fits the following automatic-transmission vehicles:2019 Nissan Versa2019 Nissan Versa Note2018 Nissan Versa2018 Nissan Versa Note2017 Nissan Versa2017 Nissan Versa Note2016 Nissan Versa2016 Nissan Versa Note2015 Nissan Versa2015 Nissan Versa Note2014 Nissan Versa2014 Nissan Versa Note2013 Nissan Versa2012 Nissan VersaKey Features:Fit: Designed to replace the slider in the shifter assembly shown in the photos. Please verify compatibility with your vehicle before purchase.Durability: Made using flexible and resilient TPU material for reliable performance, able to withstand the repeated movement inside your gear shifter assembly.Heat resistance: TPU offers heat-resistant qualities over traditional PLA filament and can survive the heat inside your vehicle during summer months. I trust it in South Texas summers that exceed 100 °F for days on end.Gear Selection Indicator Tab Included: Just like the original and unique compared to other after-market prints, it includes orange indicator tab to easily see the shifter gear position with a glance.Warranty: 2-yearDue to the nature of 3D printing, your part may differ slightly from the photos shown.If you are looking for a cost-effective and efficient fix for your shifter slider issue, this slider is the solution you have been seeking!Installation Instructions:Pre-installation:Park your vehicle in a flat, secure location to prevent rolling. Use wheel chocks if you have them.Ensure the engine is turned off and keys are removed.Ensure the parking brake is engaged.Place your foot on the brake pedal during the entire install.If you can remove the shifter cover while the vehicle remains in Park, do so. If you must change the shifter position, keep your foot on the brake, the parking brake engaged, and the engine off.Installation:Remove the gear‑selector knob and shaft cover: Slide the shaft cover down to expose the metal retainer clip.Note where the clip sits on the shifter stick so you can re-install it later.Carefully remove the clip with pliers or a screwdriver and set it aside in a safe place.Pull up on the knob and shaft cover to remove them.Remove the center‑console bezel: Remove the screws securing the console. Most likely they are near the floor in the four corners.There may be screws hidden under trim on top the center console. Carefully pry off any trim pieces to reveal hidden screws, taking care not to damage the trim.Lift the console bezel away once all screws are removed.5. Remove the top cover of the shifter unit: Locate the four clips (two per side) holding the cover.Gently pry each clip with a small screwdriver to release them. Be careful as they can be brittle from age and heat/UV exposure.Lift off the top cover.Replace the slider, making sure the orange tab is on the driver side and that it sits properly in the channel between the shifter unit and the top cover.Reassemble all components in reverse order.Test fit and function by shifting back and forth through all gears.Reassemble in reverse order.About us: Celestial Auto Parts is a brand of Celestial Fabrication, LLC is a small family business based in San Antonio, Texas, USA. We began in the mid-2010s as Nostalgia Delivered, originally specializing in the resale of vintage, antique, and nostalgic merchandise and media. In 2024, we began branching out into other services, including 3D print design and manufacturing. In early 2026 we spun-off these acties into Celestial Fabrication, LLC, dba Celestial Auto Parts. All of our 3D printed parts are modeled, printed, processed, packed, and labeled in our home, entirely within the USA! All designs are either produced in-house from scratch, are reproductions, or are sourced from online open-source databases (attribution given where necessary). We prefer American-made raw materials suppliers but may use global suppliers when domestic options are unavailable or not feasible. Thank you for supporting American small business! Made in the USA 🇺🇸 with U.S. and/or global materials.

• Fits 2012-2019 Nissan Versa and 2014-2019 Nissan Versa Note.
• Durability: Made using flexible and resilient material for reliable performance, able to survive the repeated movement it will experience inside your gear shifter assembly.
• Heat resistance: With heat-resistant qualities, it can survive the heat inside your vehicle during the summer months.
• Bright-orange gear selection indicator tab included to clearly see what gear is engaged.
• Made in the USA with U.S. and global materials
• 2 Year Warranty